Category Archives: Arduino

To Boldy Go FORTH!

1 Reply

So, as mentioned earlier, I have installed FlashForth on an Arduino Nano.

In this blog I will tell you how I did it. There are some small things that make put you of on the track there.

Get the tools

To get the things going you will need:

  • Some Arduino board (Nano, Duemilanove, Mega 2560 R3 or Uno R3)
  • A way to get the hexfile on the board. I’m using a second Nano card with the ArduinoISP sketch and avrdude.
  • The code to burn. Can be found at Source Forge (Download link).

I am running Kubuntu, so the installation of avrdude is done by:

sudo apt-get install avrdude

Unpack the FastFoth archive and find the hex file needed. In my case

~/work/flashforth-code-537e623ec97a1f9c912eba7d6c7afaafbdd0c60d/avr/hex

Get a Programmer

If you allready have an ISP system, you can skip this part.

How to hook up two  Arduino Uno to use one as an ISP for the other is shown here.

For two Nano, it is more or less the same:

PENTAX DIGITAL CAMERA

Or as a Fritzing sketch:

NanoISP_bb

 Program!

So, looking in the file “A Tutorial Guide to Programming PIC18, PIC24
and ATmega Microcontrollers with FlashForth” (found here.) I found a avrdude command to use:

$ sudo avrdude -p m328p -B 8.0 -c jtag3isp -P usb -e \
-U efuse:w:0xff:m \
-U hfuse:w:0xda:m \
-U lfuse:w:0xff:m \
-U flash:w:ff_uno.hex:i

Now, this line contains some errors for my setup. The easy ones:

I don’t use jtag3isp, I use avrisp. I have the programmer on /dev/ttyUSB0, not only usb.

There is one more problem. I don’t know if it is board, processor or programmer related. When I enter the line:

sudo avrdude -P /dev/ttyUSB0 -b 19200 -c avrisp -p m328p -v -e -U efuse:w:0xff:m -U hfuse:w:0xda:m -U lfuse:w:0xff:m -U flash:w:ff_uno.hex:i

I get an error:

avrdude: safemode: efuse changed! Was ff, and is now 7
Would you like this fuse to be changed back? [y/n] n

It seems my setup return unused bits in efuse as 0, but 1 is expected. Chaning the line to:

sudo avrdude -P /dev/ttyUSB0 -b 19200 -c avrisp -p m328p -v -e -U efuse:w:0x07:m -U hfuse:w:0xda:m -U lfuse:w:0xff:m -U flash:w:ff_uno.hex:i

does the trick.

Start playing…

To hook up to the new toy to the computer, I use:

sudo gtkterm –port=/dev/ttyUSB0 –speed=38400 –delay=10 –flow=Xon

and now I have a Forth Arduino Nano.

More on FlashForth

SourceForge page

 

On the Matter of Size

Leave a reply

When you write a more complex program that uses several libraries, you will sometimes run into a problem with that the sketch doesn’t fit in the Arduino. What to do?
You can find some ideas in the Arduino forum and elsewhere. Some ideas:

Your Own Code

Do you need all those libraries? Really? Check again.
Rewrite your code. Do you make the same 4 line code snippet in several places? Use a function. With some good comments, it will not be more difficult to read your code.
Also, try different approaches. Since the compiler uses a optimizer, the result might not be what you think.

Variable Types

Floats are often bloats… Do you really need floats? Or can you handle it with a integer that is 10 or 100 times the float value?
Remember that RAM is even more scarce than flash memory on the Arduino, and integers normally takes less memory than floats in Ram also.

 

Libraries Blues

Libraries are a good thing. You don’t have to care about the details how to handle a DHT11 or DHT21.
But they are also a bad thing for flash. There are a couple of DHT libraries out there. Some are specific DHT11, some handle DHT11 and DHT21. If you only have one of them, maybe you should go for the specific version.
To minimize the size of the code, you could be helped by reading the documentation and code. Some libraries (like uTFT library) have defines to remove unused parts.
If this is not enough, you might have to rewrite the library yourself. See this text about that.

For instance, the uTFT library uses floats and doubles to draw lines. This should be possible to work around, and save some 2kB of flash.

The Arduino Dev Kit

This is a part I didn’t expect would give me headache…
But look at these three outputs:
Binary sketch size: 27 526 bytes (of a 30 720 byte maximum)
Binary sketch size: 32 130 bytes (of a 30 720 byte maximum)
Binary sketch size: 32 150 bytes (of a 30 720 byte maximum)
This is the output from three versions of the dev kit. (1.0.5+dfsg2-2, 1.0.5, and 1.0.6).
Now, for this problem, I have so far not found a good solution. In other types of SDKs you normally can change the parameters sent to the compiler, but with the Arduino kit it isn’t that easy. I also suspect that one or more library has been ‘improved’, but this type of improvement is not needed by me.
As you can see, it is a quite big difference also, more than 4 kB.

Not using c/c++

I have an Arduino Nano with FlashForth installed. This might be a solution also. See more in an upcoming blog entry…

The toys are here!

Leave a reply

So, the mail arrived with my new toys. Too bad the weather is supposed to be sunny for some time.

IMGP4563

 

Well, I have some interesting time ahead getting the Arduion copy to work with all the parts. At least the Nanocopy works.

Also the TFT screen is connected and checked. The good news: it works! The bad news: The UTFT library takes some 80% of the flash space in the Arduino. So I need to remove more things from the library to get space for the other libraries I need.

IMGP4566 IMGP4568

Hack libraries was actually something I was expecting to have to do, since most libraries seems to have some things more or less hard wired that is not always needed or wanted.

Now, the library I found that works with my screen is a modified UTFT ver 1.3. Current version is 2.7 (Here is the latest version), so I will stick with on old version for some time. My code is on Github as UncleBod.

Now I have to continue some library hacking…

The plan takes form….

Leave a reply
test_1

First part of the plan

So, this is the plan:

 

A MCU, a temperature sensor, a combined temperature and humidity sensor, somewhere to show the readings and some keys to press.
To have a logger, let’s add a RTC and a SD card reader.
Even if I have a development board with a 90S2313 (called Attiny2313 now) somewhere, it will not be good enough for the logger function. Not enough Flash.
So, after surfing round I decided for an Arudino Nano. One reason is that I found a place that sells it for a good price. That it has USB port is another reason.

My current want to shop list….

Nano V3.0 ATmega328P-AU Microcontroller Board With USB Cable
DS1302 Real Time Clock Module Board DS1302 Module With CR2032 Battery
DS18B20 Temperature Sensor DALLAS 18B20 TO-92 Encapsulation
1.8 Inch Serial SPI TFT LCD Display Module With Power IC SD Socket
9V Battery And Battery Buckle Snaps Deduction For Arduino
Digital Temperature Humidity Sensor Module Probe For HVAC Arduino 4pin

Parts ordered:

  • Nano V3.0 ATmega328P-AU Microcontroller Board With USB Cable (1 item)
  • 40pcs 20cm Male to Male Color Breadboard Cable Jump Wire Jumper (1 item)
  • DS1302 Real Time Clock Module Board DS1302 Module With CR2032 Battery (1 item)
  • DS18B20 Temperature Sensor DALLAS 18B20 TO-92 Encapsulation (1 item)
  • DC 4 Key Matrix Membrane Switch Control Keypad Keyboard Super Slim Pad (1 item)
  • 1.8 Inch Serial SPI TFT LCD Display Module With Power IC SD Socket (1 item)
  • Digital Temperature Humidity Sensor Module Probe For HVAC Arduino 4pin (1 item)
  • 560pcs 56 Values 1/4W 1% Metal Film Resistors Assorted Kit Set (1 item)
  • 9V Battery And Battery Buckle Snaps Deduction For Arduino (1 item)
  • 300 Pcs 30 Values 2pF To 0.1uF Ceramic Capacitor Assorted Kit (1 item)

I’ve got a plan!

Leave a reply

Yea, I do. Not a really big thing. It is just getting back to electronics after some 10-15 years.

OK, I stumbled over Arduino a year back or so. Looked interesting. Even more, since I earlier had a project with a AVR chip going on at home (A hexapod, don’t ask…).

A while back I stumbled over a online shop selling Arduino copies for a very good price, so now I’m in negotiations with the wife about a small project.

The idea is to make a simple thermometer to our greenhouse. The basic first version is planned to log the temperature and humidity inside the greenhouse and temperature outside. (Future plans is to have it send the data to a central unit (we are planning a second small greenhouse, so two measurement units would be logical). Then add a GSM unit to get the data to the mobile, then add.. (OK, I think you get the idea).

The blogs on this site will be about the project, and some general rants about electronics, programming and measurements.